Web Site Search

The Clean Lubricant Polywater® G CLEAR GEL Cable Pulling Lubricant

• Clean drying and non-staining for less mess.
  
  
• Water based and water washable.
  
  
• Good friction reducing properties. For maximum friction reduction, use Polywater® J.
  
  
• Applies easily by pumping, or using the Front End Pack™ Bag System.
  
  
• Low solids will not cement-in cables.
  
  
• Evaporates after use. Nothing to soil hands or pollute environment.
  
  
• Temperature stable. No waste due to phase separation.
  
  
• Compatible with all common* cables, including polyethylene jackets.
  
  
• Proven effectiveness through decades of worldwide use.
  
  

Polywater® G is a general purpose, clean, clear, water-based, thixotropic gel lubricant recommended for all types of cable pulling, including verticals. Environmentally safe and non-toxic. (NOTE: For especially long, hot, or difficult pulls, gel-type Polywater® Lubricant J is recommended.

ORDERING OPTIONS
Catalog Number	Package Size	Units/CS	Image
G-640	5-gallon pail (18.9 liters)	1
G-128	1-gallon jug (3.8 liters)	4
G-55	½-gal Front End Pack™ bag (1.9 liters)	6	None
G-35	1-quart squeeze bottle (.95 liters)	12

1. Lubricity: PVC- or LDPE-jacketed cable on PVC conduit at 200 lbs/ft normal pressure; coefficient of dynamic friction <.23. PVC- or LDPE-jacketed cable on LDPE conduit at 200 lbs/ft normal pressure; coefficient of dynamic friction <.20.
   
   
2. Temperature stability: No more than a 10% change in Brookfield viscosity from 5°C to 38°C (40°F to 100°F). No phase-out after five freeze/thaw cycles or 24-hour exposure at 49°C (120°F).
   
   
3. Appearance: Thick, clear, colorless, gel material.
   
   
4. pH: 6.4 to 7.2
   
   
5. Wax, grease, and silicone content: None
   
   
6. Cable compatibility: No deleterious effects on physical or electrical properties of common* cable jackets.
   
   
7. Temperature Use Range: -5°C to 33°C (20°F to 90°F).
   
   
8. Percent non-volatile solids: .5 to 1.5%
   
   
9. Polyethylene stress cracking: No stress cracking on LDPE cable jacket when tested by ASTM D1693.
   
   
10. Toxicity: Non-toxic and non-sensitizing. Industrial use only.
    
    
11. Flammability: Lubricant has no flash point and dried residue is non-flammable.
    
    
12. Cleanup: Complete cleanup possible with water.
    
    

*Contact American Polywater for specific recommendations on LSZH or LSHF cable jackets.

Important Notice: The statements and information here are made in good faith based on tests and observations we believe to be reliable. However, the completeness and accuracy of the information is not guaranteed. Before using, the end-user should conduct whatever evaluations are necessary to determine that the product is suitable for the intended use. The user assumes all risks and liability in connection with such use. The statements contained herein are made in lieu of all warranties, express or implied, including, but not limited to, implied warranties of merchantability and fitness for a particular purpose, which warranties are hereby expressly disclaimed. American Polywater's only obligation shall be to replace such quantity of the product proven to be defective. Except for the replacement remedy, American Polywater shall not be liable for any loss, injury or damage, direct or indirect, arising from the use or the failure to properly use these products, regardless of the legal theory asserted. The foregoing may not be altered except by a written agreement by the officers of American Polywater Corporation.

P.O. Box 53 | Stillwater, MN 55082 USA
1-(651) 430-2270 (Voice) | 1-(651) 430-3634 (Fax)
1-(800) 328-9384 (Toll-Free US/Canada Only)

Copyright © 2001 - 2008 American Polywater Corporation | 1/28/08