Web Site Search

Reusable! Polywater® FST™ Duct Sealant Water Block Foam Kit A Reusable, Quick-Setting, Two-Part, Foam-Base Duct-Sealing System

• Seal water, dirt, oil, rodents, or other contaminants out of conduit/duct or central office
          Protect your investment in cable, electronics
          Deter copper cable thieves (see lab report)
  
  
• Seal of cured foam is strong, resilient and chemically resistant
          Provides superior protection in adverse field conditions
          and where cable movement is present
  
  
• Kit seals up to 5 ducts (50mm/2")
          Saves money over single duct products
  
  
• Foam expands and cures quickly even when water is present
          Seal ducts quickly and neatly
  
  
• Two-part foam is mixed in nozzle as it is injected
          Saves time with no measuring or mixing required
  
  
• Cured foam is low density
          Easier to cut out for cable changes or additions
  
  
• Cartridge injection system allows use of all foam base
          No wasted material
  
  
• Cartridges are marked with volume graduations (notches)
          Allows measurement of base used for different size ducts
  
  

Polywater® FST™ Duct Seal/Water Block Kit contains a cartridge with a two-part foam base that, when injected, expands and hardens, keeping out water, acids, greases, insects, rodents, etc.   It has good wetting and adhesion to metals, plastics, and concrete.   The kit contains enough material to seal up to 3 large ducts.   A separate, reusable, ratchet application tool is used to inject the foam.   The foam base is mixed in equal parts as it is pushed through the mixing nozzle.

Polywater® FST™ Duct Seal
A properly constructed FST™ Duct Seal example is shown at right in the clear conduit demo.   Note the placement of the "damming" strips wrapped around the cables.   The dams create the void into which the liquid FST™ foam is injected and hold the rapidly expanding foam in place while it cures.   Read the Application Instructions for additional information.

ORDERING INFORMATION
Catalog #	Description	Units/CS	Image
FST-180-KIT	1 6-oz cartridge (cat# FST-180) 2 24" Foam damming strips (cat# FST-DAM) 3 Mixing nozzles 1 Pair disposable gloves 1 Positioning rod for foam dam 1 Pre-treating wipe (cat# CD-1) 1 Resealing cap 1 Instruction sheet	6
FST-180	1 6-oz cartridge with 3 mixing nozzles	12	None
FST-TOOL	1 Applicator gun	1
FST-DAM	1 24" Foam damming strip	24	None
CD-1	1 Conduit pre-treating wipe	288

PHYSICAL PROPERTIES

1. Appearance: Amber color
   
2. Viscosity: Part A = 1,000 cps; Part B = 250 cps; Mixed = 600 cps
   
3. Specific Gravity: Part A = 1.23; Part B = 1.10; Mixed = 1.16; (Water = 1.00)
   
4. Reaction Time: 15 seconds
   
5. Cure Time: 5 -10 minutes
   
6. Density: 64.4 kg/m³
   
7. Compressive Strength: 13.8 MPa
   
8. Tensile Strength: 15.9 MPa
   
9. Flexural Strength: 14.5 MPa
   
10. Service Temperature: 200° F/93°C Continuous; 250°F/121°C Peak
    
11. Package: 2-part (180 ml) cylinder used to seal up to 3 ducts
    
12. Expansion Ratio: Approximately 10x

Important Notice: The statements and information here are made in good faith based on tests and observations we believe to be reliable. However, the completeness and accuracy of the information is not guaranteed. Before using, the end-user should conduct whatever evaluations are necessary to determine that the product is suitable for the intended use. The user assumes all risks and liability in connection with such use. The statements contained herein are made in lieu of all warranties, express or implied, including, but not limited to, implied warranties of merchantability and fitness for a particular purpose, which warranties are hereby expressly disclaimed. American Polywater's only obligation shall be to replace such quantity of the product proven to be defective. Except for the replacement remedy, American Polywater shall not be liable for any loss, injury or damage, direct or indirect, arising from the use or the failure to properly use these products, regardless of the legal theory asserted. The foregoing may not be altered except by a written agreement by the officers of American Polywater Corporation.

P.O. Box 53 | Stillwater, MN 55082 USA
1-(651) 430-2270 (Voice) | 1-(651) 430-3634 (Fax)
1-(800) 328-9384 (Toll-Free US/Canada Only)

Copyright © 2001 - 2008 American Polywater Corporation | 4/11/08